No hay artículos en el carro
No hay artículos en el carroQué hacer si el extremo caliente está bloqueado p>1. Configuración básica: motor de extrusora y parámetros de corte, si no sabe cómo ajustarlos, utilice los parámetros estándar. p>2. Filamento: Compruebe si hay fenómenos, impurezas, errores húmedos, polvorientos o de gran diámetro. p>3. Extrusora: la caja de cambios es resbaladiza o demasiado firme, se recomienda lubricarla o reemplazarla. 4. Tubo de PTFE: compruebe si la pared interior es lisa y resistente a altas temperaturas. p>5. Cabezal neumático: se recomienda utilizar el tipo de paso o prestar atención a la conexión durante la instalación. p>6. Tubo laríngeo/fractura de cabeza: si el efecto de enfriamiento es malo, se derrite por adelantado o se bloquea durante el proceso de extracción. p>7. Ventilador Hotend: compruebe si está instalado al revés o roto y el efecto de enfriamiento es pobre, lo que derrite el filamento por adelantado. p>8. Boquilla: Compruebe si no están apretados o el hilo residual bloqueado y la instalación está torcida. p>9. Ventilador de boquilla: ajuste la dirección, no sople la boquilla, ya que la baja temperatura no puede derretir completamente el filamento y causar obstrucción. p>Antes de reemplazarlo, dispare problemas de acuerdo con los pasos anteriores. p>
gilles
Reseñado en Francia el 24 de marzo de 2025
j'ai changer la tête d'impression de mon imprimante et je n'est pas eu de problème, l'impression qui a suivie s'est faite correctement. très bon article livrer dans las délais rien a redire pour se produit.
Mitchell K.
Reseñado en Estados Unidos el 29 de marzo de 2024
I was able to swap this right into my printer and saw as good or better prints right away. It did seem like my nozzle temperature stayed more consistent and translated to consistent layers in my print.
Andchelle
Reseñado en Estados Unidos el 13 de marzo de 2024
I ordered this as an exact replacement upgrade for my Artilllery Sidewinder X2. Im somewhat disappointed with the Hotend Performance (3/5 Stars).This hotend seemed promising at first, but unfortunately, my experience fell short. Here's a breakdown of the issues I encountered:Short Lifespan: The thermistor failed after only 3 prints that took about 20 print hours, causing significant temperature overshoot and ruined the print filament.Inconsistent Temperature Readings: The faulty thermistor led to a discrepancy of at least 40 degrees between actual hotend temperature and the reported reading. I'm still not sure if it was working properly at all.Material Concerns: The soft material used in the hotend construction resulted in constant loosening, potentially affecting print quality. It's not completely this hot end being bad, but Artillery's design for the heat break. Between the hotend and heatbreak, there is no support! The bimetal heatbreak can easily bend when hot, so beware if tightening the hotend or if the hotend hits the bed for some reason.Positive Aspects:While not a dealbreaker for me, it's worth mentioning that the fitment wasn't compatible with my Artillery Sidewinder X2 as advertised. But after I changed some x and z offset positions, it can work. Its just very complicated to change all the settings and make sure the hotend and z offset are perfectly aligned with the bed. The additional hardened steel hotend is a bonus but overkill for this hotend, as it won't even need anything beyond brass for its heatblock temp capacity being low.Overall:While the price is cheap and looks promising, the short lifespan, temperature issues, and material concerns prevent me from giving this hotend a higher rating. It might be a better fit for lower-temperature printing, but for the Artillery Sidewinder X2 or X1, I'd recommend looking for a more robust option.Rating: 3 out of 5 stars
Michael Fiebig
Reseñado en Alemania el 31 de octubre de 2024
sehr gute Ersatzteil Option sehr gute Qualität druckt einwandfrei
Chris
Reseñado en Italia el 20 de octubre de 2024
UNIXYZ Hotend per Artillery Sidewinder X1 X2E' sempre bene avere un hotend di scorta, questo della UNIXYZ è uguale all'originale, sia come pezzi che materiali usati, vi arriva tutto smontato, tranquilli, è semplice da assemblare, fate attenzione quando montate il termistore (il piccolo cilindretto) i piccoli cavi sono delicati e vanno maneggiati e piegati con delicatezza, per il resto non ci sono problemi.Insieme trovate anche un ugello in acciaio temprato più durevole e meno soggetto all'usura, inoltre dissipa meno il calore rispetto all' ottone migliorando le stampe.Un kit da avere sempre con se, insieme alle ventole di raffreddamento, montaggio semplice, funziona bene come l'originale, prezzo in linea con altri kit uguali o simili.
Productos recomendados
