No hay artículos en el carro
No hay artículos en el carroDescripción del producto
Angelique & Augis
Reseñado en Alemania el 22 de marzo de 2025
Purchased a nozzle as a future replacement to our A1 mini and after trying it out, it works great! Installation was quick and simple, prints are the same quality as the stock nozzle and with the price so low, these are an easy recommendation!✅The good stuff:- Fits perfectly (A1 Mini);- Works just as well as stock nozzle;- Extra goodies!❌ The negatives:- None! Fantastic quality to price ratio!
Veloce Mike
Reseñado en Suecia el 31 de enero de 2025
Works as it should most of the time but it seems to fluctuate a bit in temperature at times. Changeing back to the original make the temp more stable.
Cliente
Reseñado en España el 30 de enero de 2025
Tuve un problema con el hotend original de la impresora y este recambio me ha ido perfecto.
cyril mazelpeux
Reseñado en Francia el 18 de enero de 2025
Près de la Terre à la machine bon rapport qualité-prix
Gnospo
Reseñado en Italia el 10 de enero de 2025
arrivato in tempi brevissimi, ho acquistato questo estrusore per la mia bambù lab A1 perchè l’originale mi si è smontato tra le mani mentre provavo a stapparlo e allora mi sono detto di provare un estrusore che nel caso di intasamento lo avrei potuto smontare la parte finale come nelle normali stampanti 3d, ho provato questo con all’interno 3 punte di diverse dimensioni e cioè 0.4 quello classico che tuttora utilizzo tutti i giorni, la dimensione 0,6mm e 0,8mm. arriva con la parte in silicone e con una chiave per smontare la punta. io mi ci sono trovato bene e mi sento di consigliarlo.
mig8j
Reseñado en España el 21 de diciembre de 2024
Yo la he puesto en una A1 mini con AMS lite y va muy bien , supongo en la A1 irá bien ya que tienen el mismo sistema.Un saludo.
Mike
Reseñado en España el 15 de octubre de 2024
Este producto es un compatible para la serie bambu lab a1, ya sea normal o mini, el precio es muy alto en comparación al original, la calidad no puedo opinar ya que realice devolución, pero los protectores de boquilla que trae, y la boquilla se observa buena calidad, salvo el imán que fija la boquilla, que no tiene una superficie lisa y se aprecia como un arañazo.
Guillermo
Reseñado en España el 19 de septiembre de 2024
Funciona bien, sin atascos, aunque si me ha parecido caro, viendo las alternativas que hay en el mercado.
Dale Gribble
Reseñado en Estados Unidos el 28 de febrero de 2022
I purchased this set of 4 Silicone Bed Leveling Mounts for an Ender 3 Pro. Installation was straight forward, unscrew the 4 bed leveling knobs, lift the Ender 3 Pro bed, then remove and set aside the 4 springs. (Take your time and be gentle with the wires.) These silicone columns are installed with the larger opening up towards the bed. The shortest silicone column goes in the back left above the little plastic piece supporting the bed heating wires.Once they were installed and the leveling knobs were tightened I went ahead and turned the printer on and selected Auto Home. Immediately it was apparent that the nozzle was too far down. I didn't want to over tighten the bed and potentially break the new silicone columns so I moved the Z-Axis limit switch up so that the bottom of the switch's plastic bracket was a few mm above the where it was initially installed. Moving the Z-Axis switch up just a bit makes the Nozzle arm stop higher up and this allowed me to loosen the leveling knobs so that these new silicone bed leveling mounts were tight, but not smashed and bulging at the sides.Once installed I leveled the bed like normal. Auto Home, then moving the nozzle to each corner and checking for the slightest resistance with a sheet of paper at each. Afterwards I ran a few of the quick rectangular bed leveling test prints, noticed one corner was slightly off. I corrected it and then re-leveled all the corners again.These Silicone Bed Leveling Mounts are great so far. I've printed a few things that took many hours to print and have not had to re-level the bed once. The springs that came with my Ender 3 Pro required me to re-level the bed after every print and were easily my biggest annoyance with 3D Printing. Get these and try them out if you have an Ender 3 Pro, but be aware you may have to move the Z-Axis Limit Switch up a tiny bit.I'll update this review if I have issues in the future or ever have to replace these. Not re-leveling the bed between prints has made 3D Printing more enjoyable.
Productos recomendados